Skip to content
CNC machined plastics

PEEK: the high-performance plastic

PEEK is a high-performance plastic for conditions that defeat ordinary engineering plastics: continuous heat up to 260 °C, aggressive chemicals, hot water and superheated steam. It is strong and stiff, and it is inherently flame retardant.

  • High-performance semi-crystalline thermoplastic
  • 116 MPatensile strength
  • 1.31 g/cm³density
  • 162 °Cheat deflection
PEEKPEEKPlastics
Polyether ether ketone
At a glance

PEEK properties

Figures from one named manufacturer or industry data sheet, compared with our other CNC plastics. See every material side by side in the property comparison.

Density
1.31 g/cm³
Tensile strength
116 MPa
Stiffness (modulus)
4.2 GPa
Flexural strength
175 MPa
Heat deflection
162 °C
Water absorption (24 h)
0.02 %

Data source: Ensinger TECAPEEK natural (stock shapes). Typical values, not guaranteed minimums.

How it rates for prototyping

  • Clear or see-throughNot suited
  • Living hingePoor
  • Heat resistantExcellent
  • Snap fits and clipsGood
  • Strong and toughExcellent
  • Wear resistantExcellent
  • Water resistantExcellent
  • Easy to paint or plateLimited
  • Low frictionVery good
  • LightweightGood
  • Conducts heat and electricityNot suited
  • Rubber-like and flexibleNot suited
  • Chemical or corrosion resistantExcellent

Guide only. General ratings for prototyping, not a recommendation for your application. Filter every material by these needs.

Tensile strength MPa

  • PEEK116
  • Glass-filled nylon98
  • Nylon 680
  • Acrylic75
  • Acetal67
  • Polycarbonate62
  • PVC50
  • ABS32
  • Polypropylene27
  • HDPE26
  • PTFE22

Stiffness GPa

  • Glass-filled nylon5.7
  • PEEK4.2
  • Nylon 63.3
  • PVC2.9
  • Acetal2.8
  • Polycarbonate2.4
  • ABS1.7
  • HDPE0.97
  • Polypropylene0.72

Density g/cm³

  • PTFE2.15
  • Acetal1.41
  • PVC1.4
  • Glass-filled nylon1.36
  • PEEK1.31
  • Polycarbonate1.2
  • Acrylic1.19
  • Nylon 61.14
  • ABS1.04
  • HDPE0.95
  • Polypropylene0.9
Strengths and limitations

Is PEEK right for your part?

Every material has trade-offs. Knowing them up front saves time and money.

Strengths

  • Long-term service up to 260 °C (300 °C short term); melts at 341 °C
  • Strong and stiff: 116 MPa tensile, 4.2 GPa modulus, 162 °C heat deflection
  • Very good chemical resistance; resists hydrolysis and superheated steam
  • Inherently flame retardant (UL94 V-0), with good sliding, wear and creep resistance
  • Almost no water absorption (0.02 to 0.03%)

Limitations

  • High material cost compared with other engineering plastics
  • Stiffness drops above its glass transition at about 150 °C, though it stays usable well beyond that
  • Natural colour is beige and opaque
Design tips

Getting the best from PEEK

Practical points to consider when you design a part in PEEK.

01

Size the stock carefully

PEEK stock is expensive, so parts that can be machined from a smaller block or rod save more than with most materials.

02

Use it where others fail

PEEK suits continuous heat, steam, aggressive chemicals and flame-retardancy requirements that rule out ordinary engineering plastics.

03

Remember the glass transition

Stiffness falls above about 150 °C, even though PEEK stays usable up to 260 °C. Check stiffness at the working temperature.

Did you know?PEEK and PTFE share a 260 °C continuous service rating, but PEEK is more than five times stronger in tension (116 against 22 MPa).
Uses and finishes

Where PEEK is used

Parts for chemical, oil and gas, semiconductor, food, energy and aerospace equipment: seals, bushes, valve and pump parts, insulators and high-temperature components.

Finishes we offer

  • Machine
  • Smooth
  • Bead blast (matt)
  • Polished
All surface finishes
FAQ

Common questions

Common questions about PEEK. Still unsure? Contact us or call +61 3 9764 2749.

What temperature can PEEK handle?

Ensinger gives 260 °C long term and 300 °C short term. It melts at 341 °C.

Is PEEK resistant to steam?

Yes. Ensinger rates it resistant to hydrolysis and superheated steam.

Is PEEK flame retardant?

Yes. It is inherently flame retardant, rated UL94 V-0.

Sources

  1. Property figures: Ensinger TECAPEEK natural (stock shapes)
  2. Ensinger: TECAFLON PTFE natural

Please use this information as a guide only. It is a general rapid prototyping reference based on typical results, and many assumptions were made in producing it. It is not a recommendation for any particular application, so please don't use it for product design or engineering decisions. The final choice of process and material is yours; check critical properties with the material manufacturer's data sheets.

Ready to make your part?

Upload your CAD files for a free, obligation-free quote.